You are here: Home » News

News and Events

  • Introduction of heat energy conversion in the process of feed pellets drying and cooling
    05-07-2018

    In the progress of feed pellets production, products that come out of the extruder or pellet mill must be dried or cooled by certain equipment before they can be packaged, stored or sold. Therefore, drying and cooling are indispensable in the processing of these products. The heat energy conversion and utilization in this process are briefly described as follows:

  • Five factors that affect mix quality
    12-07-2017

    The pre-mix is often considered to be the key part of the compound feed. It plays a multi-functional key role in the mixing of compound feed. On the other hand, the composition is extremely complex, it has more variety, less quantity, and its physical chemistry is very different.

  • The Operation and Maintenance of the Rotary Sieve
    11-15-2017

    The rotary grading sieve is an indispensable piece of equipment in the modern feed production process. It is widely used in feed mills. During production, when some users are not operating and maintaining the equipment enough, there will be some problems.

  • Studies on the control of moisture detection in pellet feed (PART TWO)
    11-02-2017

    Methods for controlling the moisture content of pellet feedThere are two kinds of solutions for real-time on-line moisture detection and control technology of pellet feed. One is feedback control, which is online testing of the water content in the feed after cooling.

  • Studies on the control of moisture detection in pellet feed(Part One)
    10-23-2017

    Studies on the control of moisture detection in pellet feed(Part One) 1. Factors that influence the moisture content of pellet feedDuring the production of pellet feed, the water content in the finished product that will be affected by crushing, conditioning as well as other liquid additives;

  • Eight Ways To Improve The Production Efficiency Of The Granulator
    09-29-2017

    Eight ways to improve the production efficiency of the granulatorWith the development of livestock, aquaculture and improvement of industrial feed technology, pellet feed production has been commonplace in feed mills. The primary equipment in the pellet feed production process is the granulator.

  • The use of pellet feed machinery equipment
    09-20-2017

    The operation mode of pellet feed machinery is also crucial to the life span of the equipment. Check the connections of each site according to the rules of operation before use. Add a proper amount of clean lubricating oil to the running area.

  • Brief analysis on the addition of small material into the feed production process
    09-06-2017

    Brief analysis on the addition of small material into the feed production process Small materials in the process of feed processing generally refers to the content that make up less than 1% of the feed and need to be separated when weighing of trace elements such as vitamins, amino acids, drugs, att

  • Focusing on the cooling process and ensuring the quality of the pellet feed
    08-28-2017

    Focusing on the cooling process and ensuring the quality of the pellet feed The pellet feed cooling section is required to ensure that the moisture content of the granule feed meets safe storage requirements after cooling. Aside from the method of controlling the moisture content of pellet feed effe

  • A brief introduction to varying feed granulation factors
    08-21-2017

    Granulation is an important part of the granule feed process and the factors affecting the granulation are analyzed in this paper.1.Adding steamThis is one factor that is more difficult to control during the granulation process and is one of the most important factors to determine the cost,

  • Three important factors that might affect material quality
    08-14-2017

    Conditioning is essential to the granulating or puffing process. Without a good conditioning system, there will not be a good granulating or puffing effect and there will be many factors that affect the quality of the tuner, this mainly depends on the following three factors.

  • A few key points to be wary of when operating a granulating machine
    08-03-2017

    A few key points to be wary of when operating a granulating machineMain operation points of granulator:(1) the particle size of the powder has a certain proportion;(2) Purpose of feed adjustment: a. Improves production efficiency; B. Extends the service life of the ring-die;

CONTACT US

Wuxi Huamu machinery CO.ltd
Add: No.18,Jingxiang Road,Xibei Town Wuxi ,Jiangsu Province,China.
Contact person:Miss Candy
Fax:0510-83795318
P.C.:214194
E-mail:huamu@china-huamu.com   
Sales Hotline:0086-15052242220

Related News

content is empty!

Quick Links

Follow Us

Support By Bullnet      
Manage Entrance
Copyright © 2016 Wuxi Huamu machinery  Co.,LTD. All rights reserves.

Friendly Links

Contact Us